How To Clean A Shower Head – Top 3 Tips
Audio recording about how to clean your shower head.
How To Clean A Shower Head – Top 3 Tips
Is your shower head not performing like it used to? Over time mineral deposits can build up which can cause the nozzles to squirt water in all directions or clog up completely, leaving you with poor water pressure or low flow.
Here are our top tips to help get your shower head back to peak performance.
1 Rub the Nozzles
Many shower heads have flexible rubber nozzles. You can dislodge mineral buildup in these nozzles by simply massaging each nozzle with your finger. You can also try gently scrubbing the nozzles with a toothbrush.
2 Soak the Shower Head in Vinegar
There are a couple of ways to do this:
If you prefer to leave the shower head attached to the pipe coming out of the wall, you can fill a plastic bag with vinegar and wrap it around the shower head.
– Secure the bag around the head with a rubber band, tape, or a twist tie.
– Leave the bag around the shower head for a few hours.
– Remove the bag and turn on the water for a few minutes to clear the vinegar out of the shower head.
If you don’t mind removing the head from the shower pipe, you can submerge the shower head in a container full of white vinegar.
– Let the shower head soak in the vinegar for a few hours.
– Re-attach the shower head to the shower pipe and run water through the head for a few minutes to clear out the vinegar.
3 Clean the Filter Screen
To clean the filter screen, you may need to consult the shower head instruction manual. If you didn’t keep the manual, don’t panic! You can usually find it on the website or by contacting the customer service department.
In general, the filter screen is located in the part of the shower head that connects to the pipe. You will need to remove the shower head from the pipe to get to the filter screen.
In most Waterpik® brand shower heads, the filter screen can be removed by gently brushing the filter out. Or you can use tweezers/needle-nose pliers to get the screen out of the pivot ball.
Once the filter screen is out of the pivot ball, run the screen under water for a few minutes to flush out any buildup. You can also use a toothbrush to gently brush out mineral deposits.
Place the filter screen back into the pivot ball and re-install the shower head to the shower pipe.
Important Note! Harsh cleaning chemicals may damage your shower head and are not recommended for cleaning.
Your browser does not support the audio chemical element .
Is your exhibitor head not performing like it used to ? Over time mineral deposits can build up which can cause the nozzles to squirt water in all directions or clog up completely, leaving you with poor water pressure or low flow .
hera are our exceed tips to help get your shower head back to peak operation .
#1 Rub the Nozzles
many shower heads have elastic condom nozzles. You can dislodge mineral buildup in these nozzles by simply massaging each nozzle with your finger. You can besides try gently scrubbing the nozzles with a toothbrush .
#2 Soak the Shower Head in Vinegar
There are a couple ways to do this:
- If you prefer to leave the shower head attached to the pipe coming out of the wall, you can fill a plastic bag with vinegar and wrap it around the shower head.
- Secure the bag around the head with a rubber band, tape, or a twist tie.
- Leave the bag around the shower head for a few hours.
- Remove the bag and turn on the water for a few minutes to clear the vinegar out of the shower head.
- If you don’t mind removing the head from the shower pipe, you can submerge the shower head in a container full of white vinegar.
- Let the shower head soak in the vinegar for a few hours.
- Re-attach the shower head to the shower pipe and run water through the head for a few minutes to clear out the vinegar.
#3 Clean the Filter Screen
To clean the percolate screen, you may need to consult the shower head direction manual. If you did n’t keep the manual, do n’t panic ! You can normally find it on the web site or by contacting the customer service department .
In cosmopolitan, the percolate filmdom is located in the separate of the shower lead that connects to the shriek. You will need to remove the shower promontory from the pipe to get to the percolate screen.
In most Waterpik® sword shower heads, the filter screen can be removed by lightly brushing the filter out. Or you can use tweezers/needle-nose pliers to get the blind out of the pivot ball .
once the filter riddle is out of the pivot ball, run the shield under water for a few minutes to flush out any buildup. You can besides use a soup-strainer to gently brush out mineral deposits .
topographic point the filter screen door spinal column into the pivot ball and re-install the shower head to the shower pipe .
Important Note! Harsh clean chemicals may damage your shower head and are not recommended for clean .
Considering a Replacement Shower Head?
Replacing a shower head is quick, easy and may reduce your department of energy and water bills.
Share This Article
Tweet
