Foam Crown Molding: 11 Steps to Elegant Decor (VIDEO) – This Old House

Project details

Skill

1

out of

5

easy
The materials are lightweight and the initiation method acting identical forgive .

Cost

About $120 for a 10-by-10-foot room

Estimated Time

3 hours per day

crown cast makes it to the top of most remodel lists because it adds charm and value to a home, but depending on what kind of peak model you use, it can be either a breeze to install or a fuss .
If you don ’ t want to take up an integral Saturday trying to get the corners precisely right, there ’ s a simpleton manner to beat miter-saw frustration. Trimroc molding from Canamould Extrusions is a lightweight polystyrene foam coated in hard plaster. It cuts smoothly with a handsaw, and, as This Old House aged technical editor Mark Powers shows here, it goes up in a flash with roast compound. No cope, no catchy angles, and ragged joints disappear with a dab of mud .

Is foam crown molding any good?

Compared to wood, foam crown mold is not only low-cost and easy to install, but it ’ s besides pliable—making it easy to work with around the curvatures of your home .

Can you paint foam crown molding?

Yes. With foam pate molding, you can either spray paint or paint by hand. TOH ’ s Mark Powers demonstrates the latter. All you need is a couple coat of sealant and some latex paint paint. ( Refer to Steps 10 and 11. )
call Canamould Extrusions at 866-874-6762 for neckcloth and custom-made orders and receive deduction ship to the United States .

Steps on How to Install Foam Crown Molding

1. Lay Out and Cut the Molding

If you ’ ra working with walls that are out of level and plumb, allow your eye, quite than a level, to guide the position of the determine. For best results, focus on getting the crown to look parallel with any neighbor snip. Install it starting at an inside corner and sour toward any outside corners. Hold a strip of molding in place above a door or window case. Adjust the determine until it looks even with the casing ( ask a assistant to stand back and look for you ). Draw a pencil wrinkle to mark this position sol that you can install the crown at this conjunction .

2. Cut an Inside or Outside Corner

To cut the molding at an angle for an inside or external corner, set it in a miter box upside down and braced against the buttocks and english of the box, as if it were angled against a ceiling and wall. Using a handsaw, cut the molding at a 45-degree angle. On an inwardly corner, the top partially of the shape will be shorter ; on an outside corner, the bottom part will be shorter .

3. Make a Tight Fit

Using a rasp or sanding parry, shave the back of the fish write out to create room for the two corners to come together tightly at the face.

Tip: Because straight butt joints are so easy to hide with this model, you can cut the pieces shorter to make it easier to work .

4. Install the Molding

The crown adheres to the wall with joint compound, but using excessively much will allow it to slide down the wall. As the compound sets, support long runs of molding with 8d nails .
Using a 6-inch putty knife, spread a ½-inch drop of joint colonial the duration of the determine along the top and bottom edges. Spread mud liberally on each cut goal .

5. Match the Profiles First

Push the two mitered ends together to create the inside corners, making indisputable their faces align in the corner. Match up the contingent of the visibility first, then use mire to fill any small gaps between the model and the ceiling on either side .

6. Fit Together an Outside Corner

On an outside corner, press the miter ends together until mud squeezes out of the joint. Backfill gaps using your feel or a putty knife .

7. Use Nails to Brace Long Runs

Along neat runs, push the straight-cut ends to create a target joint. On long runs, place an 8d complete under the shape every few feet and at joints to hold it in target. Angle the nails up slenderly to hide the holes, and sink them adequate to keep them in stead .

8. Smooth the Joints

Cleanup will be easier if you clear away excess joint compound while it ’ second still wet .
Use your finger to smooth out the seam where the mold meets the wall and the ceiling. Use a wet leech to help wipe away the intensify and clean up the face of the molding. Don ’ triiodothyronine remove besides a lot compound—if you do, the seams will “ hollow ” as it dries .

9. Fill to Excess

Using a little putty knife, push more compound into and over butt joints. Pull the knife over each detail of the profile, leaving the compound a fiddling proud of the roast. once dry, the excess can be sanded smooth .

10. Prep to Paint

joint compound is slowly to sand, and once you go over the seams where molding meets molding, the joints will about disappear .
After the articulation compound dries completely, sand down the surfeit using 150-grit emery paper .

11. Mask and Paint

Mask the walls along the edges of the mold with painter ’ randomness tape. Using an fish girdle brush, prime and paint the molding to match the door and windowpane casings in the room .

Tools

source : https://meopari.com
Category : How To