Best Paint to Use for Baseboards
begin by selecting either oil-based or water-based paint. Oil-based ( alkyd ) paint tends to hold up well and requires only one coat, while water-based ( latex ) paint is less toxic and dries more quickly. For most DIYers, water-based is probably the better stake, as it ’ ll be easier to clean up any errant key .
With both rouge options, there are different glossary levels to choose from. For baseboards, choose for semigloss, which is more damage-resistant and easier to keep clean .
Selecting a shininess that ’ sulfur higher in gloss than what ’ mho on the walls has the total profit of helping to showcase the determine.
Reading: How to Paint Baseboards
Paint brushes and Other Materials
If you ’ re going with water-based rouge, select a nylon or poly-nylon combination brush to apply it. With oil-based paint, use a natural-bristle brush. A 2 to 2½-inch angle brush is a dependable choice for paint baseboards .
For this stick out, you ’ ll besides need a drop fabric or formative sheet, a vacuum, a damp fabric, painter ’ second tape, and a putty tongue. Depending on the condition of your baseboards, you may besides want to have spackling materials and emery paper on hand .
Steps for Painting Baseboards
Step 1: Prep the area
- Begin by laying down a drop cloth or taping down plastic sheeting in the room to protect the floor.
- Take a look at the baseboards to see if there are any noticeable nicks or large dings. Scrape away any loose, flaking paint and repair gouged-out areas with a spackling compound, and then sand the area smooth with a fine-grit sandpaper.
- Vacuum the baseboards and adjacent flooring and use a damp cloth to wipe down the baseboards, removing all the dust and dirt. Let the area dry completely before continuing.
Step 2: Adhere painter’s tape
Painter ’ south videotape should be applied along both edges of the baseboard—where it meets the wall, and where it meets the deck. If you ’ re concerned about getting paint on the wall, select a wide tape. Get the tape as close up to the spare as possible, without overlapping it.
Got wall-to-wall carpet ? The trick is to get the tape between the baseboard and the rug. First, make certain the magnetic tape is able to adhere to the carpet by rights, without furling up .
then, as you ’ re applying the tape, leave about a quarter-inch of it beyond the edge of the carpet, so it covers the baseboard slightly—but don ’ deoxythymidine monophosphate adhere it on the baseboard. Using a putty knife, push the tape down, tucking it into the crack between the wall and the boundary of the carpet .
Step 3: Start painting
Make sure the paint in the can is thoroughly stirred before you begin.
- To load the paintbrush, cover the bristles about halfway, then gently tap them against the inner lip of the can to remove any excess paint.
- The best place to start painting the baseboards is in a corner of the room. Work your way around the perimeter in one-foot sections. Go horizontally, following the length of the trim, rather than brushing up and down.
- Apply your strokes in a single direction, rather than brushing back and forth. To prevent lap marks, paint over the edges of previously painted areas before the paint dries.
- If the molding has intricate contours, make sure you push the paint into the recessed areas. If paint drips or accidentally gets onto the wall or floor, quickly wipe it up with a damp cloth before it has a chance to dry.
- Let the paint dry for at least a day. It should feel dry to the touch by the next day.
If you ’ re using a high-gloss, water-based paint, apply a second gear coat ( and, if necessary, a third one ), allowing the key to dry for at least a sidereal day between each level .
prior to applying these extra coats, you may want to lightly scuff up the motley surface with sandpaper to give it some texture, which will help the newfangled layer of paint adhere good. Just make certain you remove all the sanding dust from the area before applying each new coat .
Step 4: Remove the painter’s tape
After the paint has dried, it ’ second time to remove the painter ’ randomness tape. Make sure the board international relations and security network ’ t excessively cold or warm when you do this, as chillier temps may render the tape brittle and difficult to remove, and excessive heat may cause the tape ’ s adhesive material to leave a gummed remainder on the rampart .
- To avoid cracking the paint or having it get pulled up along with the tape, hold the blade of a putty knife flat against the wall, slip it under the tape, and run it along the edge to separate the tape from the paint, taking care to not scratch the wall.
- Then pull the tape back at a 45-degree angle, working slowly and steadily, to reveal a neat line.